- GARMIN ANT AGENT ON WINDOWS 10 HOW TO
- GARMIN ANT AGENT ON WINDOWS 10 FOR MAC
- GARMIN ANT AGENT ON WINDOWS 10 INSTALL
- GARMIN ANT AGENT ON WINDOWS 10 DRIVER
- GARMIN ANT AGENT ON WINDOWS 10 WINDOWS 10
You might also ping Garmin and tell them there is an issue with their Mac driver being more active then would otherwise be nice. If you have found a solution please let me know. I have hundreds of runs that are broken up into different folders in different years, but thus far any and all attempts to migrate this data from the Windows Training Center to the Mac Training Center has resulted in what I consider an unindexed mess - everything is put back in pure date order, and all division by Event, Location, etc. I have been using the Garmin Training Center in Windows for several years and I was stunned at how non-compatible the Mac version has turned out to be.
GARMIN ANT AGENT ON WINDOWS 10 FOR MAC
The pesky driver is related to the SiLabsUSBDriver for the Garmin ANT that the driver for Mac sets up in the following location: ~System/Library/Extensions/SiLabsUSBDriver.kext If it was in place I could not get the ANT agent in Windows to work, but deleting it made everything work again. With a test system I found that indeed the driver (when it installed without a hitch) was the issue. My corruption seemed to get so bad that I actually resorted to Archiving and Reinstalling OS X. HOWEVER - the Mac environment uses a driver for the Mac environment will utterly corrupt any attempt to get the ANT working in your Windows Virtual Machine. If that program is on, make sure you exit it. Check for Garmin ANT Agent, or Garmin Express in the system tray. Since a sync has been successful after the activity in question, it sounds like the 910XT cannot create a valid.
GARMIN ANT AGENT ON WINDOWS 10 INSTALL
The install for me did not go smoothly, but eventually I got it working - at least for the Mac side of things. If the drivers are installed properly, but TrainerRoad cannot find the ANT+ USB stick, there may be conflicting programs as only one program can access the ANT+ USB stick at a time. The catch is that if you REMOVE the Ant you have to catch it again during the next boot up or else you will crash the system again.Īlso - you may have found that Garmin now has the ANT agent for the native Mac environment. Once either is done, the setting remains sticky so you can boot up and down and all is good. You can also click into settings and then click the box while the Virtual Machine is loading - but that is tricker to pull off. When the Virtual Machine is loading you can simply click on the grey USB icon and it will go black - then the ANT stick will be seen by Windows as it loads and kernel panic will be avoided. Ok, so to get the ANT set BEFOER windows was fully loaded I found two options. However, upon restarting the Virtual Machine the Ant was not automatically registered, and when I clicked on the grey icon for USB which identified itself as the Dynastream ANT2USB in the bottom window bar or went into settings and clicked on the check box I was greeted with a kernel panic and instructions about holding the power button to restart. When I went through the install process for the ANT, I got to the point where I was told to install the ANT stick and I did - the system found it and it seemed like life would be fine. As you have already seen in the other responses to your post, folks are aware of this kernel panic issue and perhaps we will see a solution sometime in the near future.īut here is what I did - let me give a bit of framing to be sure you are experiencing the same events along the way. Microsoft makes no warranty, implied or otherwise, about the performance or reliability of these products.I went through this same issue, and found at least a partial solution. The third-party products that this article discusses are manufactured by companies that are independent of Microsoft. To download the latest Garmin Express tool, go to Garmin Express.
GARMIN ANT AGENT ON WINDOWS 10 WINDOWS 10
This issue is documented by Garmin at the following site:ĭevice is not detected in Windows 10 after updating to the Anniversary update. The Garmin Express tool recognizes the connected device and updates its boot code to make it compatible with Windows 10. To resolve the issue, download and install the latest version of Garmin Express software. This problem occurs because Garmin devices formatted with FAT12, FAT16, or FAT32 file systems aren't recognized as mass storage devices by a computer or device that's running Windows 10.
Attempts to access the drive trigger errors such as the following ones: Garmin ANT Agent detects any paired Garmin.
GARMIN ANT AGENT ON WINDOWS 10 HOW TO
This article provides information on how to fix the problem that Garmin wearable devices aren't recognized on Windows 10.Īpplies to: Windows 10, version 1709, Windows 10, version 1607 Original KB number: 3183365 SymptomsĪfter you upgrade a computer or device to Windows 10, certain Garmin wearable devices may not work as expected when they're connected to a USB port.Īlthough the Garmin device shows up in Device Manager and is displayed as a connected drive in File Explorer, it isn't accessible. Garmin ANT Agent allows you to transfer fitness data from compatible Garmin ANT devices to and from your computer.
0 kommentar(er)
